Home > Textbooks > Lessons In Electric Circuits > Vol. I - DC > Series-Parallel Combination Circuits > Component Failure Analysis

Chapter 7: SERIES-PARALLEL COMBINATION CIRCUITS

# Component Failure Analysis

"I consider that I understand an equation when I can predict the properties of its solutions, without actually solving it."

P.A.M Dirac, physicist

There is a lot of truth to that quote from Dirac. With a little modification, I can extend his wisdom to electric circuits by saying, "I consider that I understand a circuit when I can predict the approximate effects of various changes made to it without actually performing any calculations."

At the end of the series and parallel circuits chapter, we briefly considered how circuits could be analyzed in a *qualitative* rather than *quantitative*
manner. Building this skill is an important step towards becoming a
proficient troubleshooter of electric circuits. Once you have a
thorough understanding of how any particular failure will affect a
circuit (i.e. you don't have to perform any arithmetic to predict the
results), it will be much easier to work the other way around:
pinpointing the source of trouble by assessing how a circuit is
behaving.

Also shown at the end of the series and parallel circuits chapter was
how the table method works just as well for aiding failure analysis as
it does for the analysis of healthy circuits. We may take this
technique one step further and adapt it for total qualitative analysis.
By *"qualitative"* I mean working with symbols representing
"increase," "decrease," and "same" instead of precise numerical figures.
We can still use the principles of series and parallel circuits, and
the concepts of Ohm's Law, we'll just use symbolic *qualities* instead of numerical *quantities*.
By doing this, we can gain more of an intuitive "feel" for how
circuits work rather than leaning on abstract equations, attaining
Dirac's definition of "understanding."

Enough talk. Let's try this technique on a real circuit example and see how it works:

This is the first "convoluted" circuit we straightened out for analysis in the last section. Since you already know how this particular circuit reduces to series and parallel sections, I'll skip the process and go straight to the final form:

R_{3} and R_{4} are in parallel with each other; so are R_{1} and R_{2}. The parallel equivalents of R_{3}//R_{4} and R_{1}//R_{2} are in series with each other. Expressed in symbolic form, the total resistance for this circuit is as follows:

R_{Total} = (R_{1}//R_{2})--(R_{3}//R_{4})

First, we need to formulate a table with all the necessary rows and columns for this circuit:

Next, we need a failure scenario. Let's suppose that resistor R_{2}
were to fail shorted. We will assume that all other components
maintain their original values. Because we'll be analyzing this circuit
qualitatively rather than quantitatively, we won't be inserting any
real numbers into the table. For any quantity unchanged after the
component failure, we'll use the word "same" to represent "no change
from before." For any quantity that has changed as a result of the
failure, we'll use a down arrow for "decrease" and an up arrow for
"increase." As usual, we start by filling in the spaces of the table
for individual resistances and total voltage, our "given" values:

The only "given" value different from the normal state of the circuit is R_{2},
which we said was failed shorted (abnormally low resistance). All
other initial values are the same as they were before, as represented by
the "same" entries. All we have to do now is work through the familiar
Ohm's Law and series-parallel principles to determine what will happen
to all the other circuit values.

First, we need to determine what happens to the resistances of parallel subsections R_{1}//R_{2} and R_{3}//R_{4}. If neither R_{3} nor R_{4} have changed in resistance value, then neither will their parallel combination. However, since the resistance of R_{2} has decreased while R_{1} has stayed the same, their parallel combination must decrease in resistance as well:

Now, we need to figure out what happens to the total resistance. This
part is easy: when we're dealing with only one component change in the
circuit, the change in total resistance will be in the same direction as
the change of the failed component. This is not to say that the *magnitude* of change between individual component and total circuit will be the same, merely the *direction*
of change. In other words, if any single resistor decreases in value,
then the total circuit resistance must also decrease, and vice versa.
In this case, since R_{2} is the only failed component, and its resistance has decreased, the total resistance *must* decrease:

Now we can apply Ohm's Law (qualitatively) to the Total column in the table. Given the fact that total voltage has remained the same and total resistance has decreased, we can conclude that total current must increase (I=E/R).

In case you're not familiar with the qualitative assessment of an equation, it works like this. First, we write the equation as solved for the unknown quantity. In this case, we're trying to solve for current, given voltage and resistance:

Now that our equation is in the proper form, we assess what change (if any) will be experienced by "I," given the change(s) to "E" and "R":

If the denominator of a fraction decreases in value while the numerator stays the same, then the overall value of the fraction must increase:

Therefore, Ohm's Law (I=E/R) tells us that the current (I) will increase. We'll mark this conclusion in our table with an "up" arrow:

With all resistance places filled in the table and all quantities
determined in the Total column, we can proceed to determine the other
voltages and currents. Knowing that the total resistance in this table
was the result of R_{1}//R_{2} and R_{3}//R_{4} in *series*, we know that the value of total current will be the same as that in R_{1}//R_{2} and R_{3}//R_{4} (because series components share the same current). Therefore, if total current increased, then current through R_{1}//R_{2} and R_{3}//R_{4} must also have increased with the failure of R_{2}:

Fundamentally, what we're doing here with a qualitative usage of Ohm's
Law and the rules of series and parallel circuits is no different from
what we've done before with numerical figures. In fact, its a lot
easier because you don't have to worry about making an arithmetic or
calculator keystroke error in a calculation. Instead, you're just
focusing on the *principles* behind the equations. From our table above, we can see that Ohm's Law should be applicable to the R_{1}//R_{2} and R_{3}//R_{4} columns. For R_{3}//R_{4},
we figure what happens to the voltage, given an increase in current and
no change in resistance. Intuitively, we can see that this must result
in an increase in voltage across the parallel combination of R_{3}//R_{4}:

But how do we apply the same Ohm's Law formula (E=IR) to the R_{1}//R_{2} column, where we have resistance decreasing *and* current increasing? It's easy to determine if only one variable is changing, as it was with R_{3}//R_{4},
but with two variables moving around and no definite numbers to work
with, Ohm's Law isn't going to be much help. However, there is another
rule we can apply *horizontally* to determine what happens to the voltage across R_{1}//R_{2}: the rule for voltage in series circuits. If the voltages across R_{1}//R_{2} and R_{3}//R_{4} add up to equal the total (battery) voltage and we know that the R_{3}//R_{4} voltage has increased while total voltage has stayed the same, then the voltage across R_{1}//R_{2} *must* have decreased with the change of R_{2}'s resistance value:

Now we're ready to proceed to some new columns in the table. Knowing that R_{3} and R_{4} comprise the parallel subsection R_{3}//R_{4},
and knowing that voltage is shared equally between parallel components,
the increase in voltage seen across the parallel combination R_{3}//R_{4} must also be seen across R_{3} and R_{4} individually:

The same goes for R_{1} and R_{2}. The voltage decrease seen across the parallel combination of R_{1} and R_{2} will be seen across R_{1} and R_{2} individually:

Applying Ohm's Law vertically to those columns with unchanged ("same") resistance values, we can tell what the current will do through those components. Increased voltage across an unchanged resistance leads to increased current. Conversely, decreased voltage across an unchanged resistance leads to decreased current:

Once again we find ourselves in a position where Ohm's Law can't help us: for R_{2}, both voltage and resistance have decreased, but without knowing *how much*
each one has changed, we can't use the I=E/R formula to qualitatively
determine the resulting change in current. However, we can still apply
the rules of series and parallel circuits *horizontally*. We know that the current through the R_{1}//R_{2} parallel combination has increased, and we also know that the current through R_{1}
has decreased. One of the rules of parallel circuits is that total
current is equal to the sum of the individual branch currents. In this
case, the current through R_{1}//R_{2} is equal to the current through R_{1} added to the current through R_{2}. If current through R_{1}//R_{2} has increased while current through R_{1} has decreased, current through R_{2} *must* have increased:

And with that, our table of qualitative values stands completed. This particular exercise may look laborious due to all the detailed commentary, but the actual process can be performed very quickly with some practice. An important thing to realize here is that the general procedure is little different from quantitative analysis: start with the known values, then proceed to determining total resistance, then total current, then transfer figures of voltage and current as allowed by the rules of series and parallel circuits to the appropriate columns.

A few general rules can be memorized to assist and/or to check your progress when proceeding with such an analysis:

- For any
*single*component failure (open or shorted), the total resistance will always change in the same direction (either increase or decrease) as the resistance change of the failed component. - When a component fails shorted, its resistance always decreases.
Also, the current through it will increase, and the voltage across it
*may*drop. I say "may" because in some cases it will remain the same (case in point: a simple parallel circuit with an ideal power source). - When a component fails open, its resistance always increases. The
current through that component will decrease to zero, because it is an
incomplete electrical path (no continuity). This
*may*result in an increase of voltage across it. The same exception stated above applies here as well: in a simple parallel circuit with an ideal voltage source, the voltage across an open-failed component will remain unchanged.